![]() ![]() So plan for that extra expense ahead of time so you aren’t surprised later.īest Option For: Interior use for all floor types. While it is among the most affordable options, no primer is included, but primer is required. It also comes in 50-pound bags and depending on your retailer, it will cost you only about $30 per bag. ![]() It has a simple mix ration that will pour to between 1/8 and 1-inch thick. The Novoplan 2 Plus is rated for all indoor applications and engineered floors. For all other flooring types that wait will extend to 48 hours. For ceramic and porcelain tiles you should wait at least 24 hours. You will need a full cure before you add most flooring types, though. The initial set time after pour is about 15 minutes. Mapei has several types of self-leveling concrete and the water-based Novoplan 2 Plus is among their best. Each one is rated and compared so you know exactly what to expect. Top 5 Self-Leveling Concrete Brands Reviewedīelow we review the best self-leveling concrete brands. If so, you can install your chosen flooring option as you see fit. Everything should be smooth, even and level. Once the cure time has been reached you can walk on the flooring and test it out. Your particular compound and brand will have a specific cure time, which is generally 14 to 24 hours for plank and tile flooring and up to 72 hours for wood flooring. Once the initial set is in, you can walk on it, but shouldn’t. In general, though you will need to wait at least 2 hours for it to be hard.ĭuring this time, you should be proactive in preventing anything from touching the surface, including tools, clothing, feet, pets, or even debris. The set time will vary by brand, amount mixed and depth of the pour. Once you are satisfied, it is time to wait. Use the trowel to push the mix to corners or areas that don’t have a lot of coverage or are bare. You will have between 5 and 10 minutes before the mix starts to harden. Note: keep using the drill and paddle to mix the solution until you actually start pouring. You will want to start in the opposite corner from the room exit and start pouring. Use the drill and paddle to thoroughly mix the solution until it is a runny, paint-like texture. Read the instructions for proper mixing and add the compound mix to the water, not the water to the compound. A trowel will also help spread the mix to areas that don’t get an even layer of coverage and a few towels to help clean up and splashes or spills before the compound dries. You also need a good drill with an extension and a cement paddle. ![]() First you should have a large bucket to mix in. While there are mixing kits, you only need a few things. Make sure the repairs or patches are dry and if you have to apply a primer or moisture barrier that it is down and ready for the concrete. You won’t need to put on your running shoes, but you won’t have but a few minutes. You will have a limited time between mixing and pouring before the concrete starts to set. You will have to be precise and expect to move fast. Along with the primer (if needed) your floor is ready to go. ![]() If you have deep cracks, joints or extensive damage, you also want to patch those first. You should check if your product includes a primer. However, if you don’t clean the floor, those impurities will resurface. Since the concrete will cover all of this, you won’t have to worry about seeing the imperfections later. You want to clean the floor as best as you can, making sure to get all the edges and in any cracks or grooves that are present. Remove all the furniture, remove the old flooring and then it is time to get out the vacuum and broom. CleaningĬleaning is important so you don’t introduce any impurities into the mix that can cause problems in the future. Once the old flooring is removed, it is time to clean. Remove old vinyl, laminate or planks until you get down to the concrete or plywood subfloor that you will then level. You want to bring the floor down to the foundation or existing subfloor first. This can create an unsteady surface, air pockets will collapse and the entire floor could crack or bubble. While it is possible for some types of self-leveling concrete to cover existing flooring, it isn’t recommended. Most important, though, is getting the floor ready. This will include your tools, buckets, water, and of course the concrete mix. Preparationīefore you do anything you should get the space ready. However, the basic steps are the same and are outlined here. You should follow all manufacturer’s instructions for the brand and type of concrete you purchase. ![]()
0 Comments
Leave a Reply. |